We've stumbled on this post about How to Install a Bathtub Yourself listed below on the web and accepted it made good sense to relate it with you on my blog.
Mounting a tub isn't exactly brain surgery, however it does need solid plumbing, woodworking, and occasionally, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably difficult task. If the old tub is readily obtainable, the job can relocate immediately; if you have to open up a wall surface to remove the old bathtub and position the brand-new bathtub, the job is much harder. In either situation, the task is within a home handyman's skills, although you will certainly need an assistant to leave the old bathtub as well as embeded in the new one. Make sure you have actually qualified yourself for the task and fit attempting it. Instead of hiring a specialist to take over a halfway-completed job, it is far better to think about using one before you start. Chances are you might need an expert plumber to make tube connections.
This write-up will assist you install a new bath tub in your bathroom if you have actually currently purchased a new bathtub and also don't require to transform the setup of your previous supply of water pipelines.
Your devices and product list should make up the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, after that the first thing you need to do is disconnect the supply of water. After doing so, activate the faucets to drain any water remaining in the system. The process of eliminating the existing faucets can be rather bothersome as a result of the limited access that is often the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipelines. When the supply pipelines have actually been eliminated, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleaned of any kind of old securing compound.
Before moving on to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new taps are plastic, after that you will need a plastic adapter to prevent damages to the string. One end of the connector fits on the plastic tail of the tap and also the other end provides a link to the existing supply pipes.
If you need to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washers are in area in between the faucet as well as the sink. Secure the faucet in position with the supplier given backnut. When the tap is firmly in position, the supply pipes can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet ports. The former kind ought to be attached to the tap ends initially, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Bath tub
Using both wooden boards under its feet, place the tub in the needed position. The wood boards are valuable in evenly spreading out the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four little points.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the bath tub up until the level checks out degree.
To install faucets, fit the bottom of the outermost flexible faucet port to the appropriate supply pipe by making a compression sign up with; then do the exact same for the various other faucet.
Switch on the supply of water as well as examine all joints and also new pipework for leaks and also tighten them if necessary. Fill the tub as well as additionally examine the overflow outlet and also the normal outlet for leakages.
Ultimately, fix the bath paneling as explained in the supplier's user's manual. Tiling and also securing around the bathtub ought to wait up until the bath tub has actually been used a minimum of when as this will certainly resolve it into its final setting.
Getting ready for the Setup
To start with, the sustaining structure supplied with the bath ought to be fitted (if needed) according to the maker's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to make sure that if the tap comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to stop pressure on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you utilize all of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to now be ready to be suited its last setting.
Tiling Around the Bathtub
In the area where the bathroom satisfies the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to crack an inflexible seal, creating the water to permeate the wall in between the bathroom and the tiling, leading to difficulties with moisture and possible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched newspaper or soft rope. Remember to always load the tub with water before securing, to enable the activity experienced when the bathtub is in usage. The sealer can crack fairly very early if you do not consider this movement prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily readily available on the market. It is suggested to fit the tiles making use of water-resistant or water-proof adhesive and also grout.
Bathtub Installation
How Important Is A Bathtub To Your Home?
High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.
Install Piping Before Tub
You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.
Position the Tub
Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.
NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.
Assemble Drain Connections
Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.
Place a Pipe For the Shower Head
First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.
Attaching Hot and Cold Water Lines
Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.
Install the Spout
Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.
NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.
Check For Leaks
Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.
estore the Bathroom Wall
Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.
https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/
I discovered that piece on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when doing a search on the web. Liked our entry? Please share it. Let other people locate it. Thanks for your time spent reading it.
Click For More Info